Wearable Lie Detector

Nemo Hsiao and 2 Otherssunny tu
Annika Cunningham

Video

Caden Krauter and 2 OthersSophia Thurau-Gray
Michele Zaccagnini

We created a hoverbord that could survive in a Sci-Fi world where 80% of the world is lava.

Video In Darkness

Charlotte Francis

Final

Joshua Fairman and William Crane

Process

Joshua Fairman and William Crane
1 / 9

Final

Michele Zaccagnini and 2 OthersSophia Thurau-Gray
Caden Krauter

The world that would need this invetion is a world that is one huge volcano. The main idea is for the hoverboard is to safely transport people across lava. As the hoveboard is rc, you would need someone to control the hoverboard within range of their vison so they can see you. The problem is that it spins around like crazy when it hovers. We are trying fix that for the time being. The project is important because it can transport stuff across long distances if you tape a camera to it and sync it to a iphone or ipad to see where you are going.

Process

Michele Zaccagnini and 2 OthersSophia Thurau-Gray
Caden Krauter

We created a hoverbord that could survive in a Sci-Fi world where 80% of the world is lava.

We made our first prototype out of cardboard and tape. It had cardboard fans and also used a fan for steering.

Then we added a fan that was pretty weak and didn't budge. Then we made it out of thin wood and added even better fans that would go berzerk if you didn't hold it.

Our final model was mad of foamcoare and had domes to protect the fans from little fingers.it was RC and had a steering fan and rudders for steering.

 

Process

Griffin Kissam and Seth Gillett
1 / 12

In a world where humans are isolated and live hundreds of miles apart in oases in a worldwide desert, it became necessary to find alternate means for communication and trade. There are many challenges in traveling through the desert, such as the notorious sand pirates who make a profitable living from robbing caravans of goods. To circumvent this, the armored train "desert snake" or "desert viper" was invented. It's outer carapace makes it very hard to breach from the ground, and its winding pattern makes it even harder to hit from the air. In addition, cars cannot be separated from each other, making sure that they cannot be divided and taken down individually.

One of the first challenges we faced was the weight of the train, particularly in the driving cars in the front and the back. This forced us to use larger and heavier motors to pull the cars, and thicker axles to ensure that the weight of the driving cars could remain in suspension. A bent axle could be fatal in an encounter with pirates, slowing the train and allowing it to be captured or destroyed.

Our very first iteration did not have wheels, much less move. This iteration was designed to test different styles of connection between the cars. Initially, we thought motors with reels connected to the exterior of each car could use rubber bands to pull and push the cars in front and behind into the winding motion necessary for our design, but this design was impractical, as it would require motors attached to each car.

Our second iteration was an attempt to create a drivable vehicle, but that was around the time we were forced to switch to heavier motors, and we found that the motors holes we had cut out were not large enough, and were forced to recraft our design.

In our third iteration, we added circular wooden wheels that could touch the ground, and bigger cars that were connected to each other by rectangular wooden sections. Now we had motors, however we found that the wheels we had created gained no friction on the wooden surface of our table, much less a sandy desert. Another problem was that our cars were too large, and wasteful of materials. We planned to have a larger number of smaller cars rather than a smaller number of larger cars. That way, we could produce a smoother winding motion in the overall train.

In our fourth iteration, we fit rubber bands around our wheels, and made the cars smaller. We also put ball-bearings on each car to allow them to move horizontally from side to side as well as forward and backward. Since cars would not be equipped individually with motors and wheels, they did not need to be self driving, part of the advantage of having a train instead of a caravan. We were also forced to elevate the car connectors, as their rotation was being blocked by the knuts connecting the ball bearings to the cars.

On our fourth iteration we added a driving car in the rear of the train, as well as in the front, to produce the curving motion we needed. The only problem was, the front car was very open and vulnerable. As demonstrated in our fourth picture above, fire would be an issue to a train not constructed of metal. To meet this end, we printed our front car in a different material in 3d, making protected compartments for the electronics required to drive the train.

After we printed our front and back cars, we distributed the electronic components along the train. The micro computer programmed to imitate the motion of a winding snake, along with the receiver allowing it to be remotely controlled was placed in the front driving car. The 9v power supply was placed in the back. The two essential components were connected by wires running the length of the train. Our final iteration was our first iteration that was drivable, and it worked just as expected.

Video

Rosa Weinberg

Process

Callum Schnee and David Shaw
1 / 14

In a world where aliens have invaded and destroyed New York City, the iron structures of the skyscrapers are all that is left. Humans have developed this vehicle to climb up the frames and escape from the aliens whose inner magnetism render the iron structures deadly. 

Our first prototype explored using sticky or magnetic mecanum wheels attached to a normal rectangular chassis. Mecanum wheels allow a vehicle to move in any direction without turning. There were problems with using mecanum wheels to transition from floor to wall to ceiling and ultimately we decided to go in a different direction. 

The second prototype was a triangular prism with magnetic wheels on all three edges so they could snap on to metallic walls. In the end we decided that a triangle shape would be cool, but it would be complicated and would not properly fit our needs. 

For our third prototype, we decided on a cube shape with magnetic tank treads, rather than wheels. We chose tank treads because it allowed us to have a larger surface area on the wall at one time. This design would also potentially be able to go across ceilings. 

The first model of our tank treads were good and steady, but had a few minor imperfections, such as friction between treads, and were not magnetic. 

The second design fixed the friction issues and allowed the treads to hold magnets. This model, though, made the frames too thin around the magnets, so they broke often. 

Our third and final tank tread design made the frame around the magnet thicker. The result was a tank tread that both looked better and worked better. We 3-D printed all the tank treads and laser cut all the frames for the magnets. After producing all the small parts on a large scale, we glued them together with epoxy.

After the motors and treads were assembled on the cube, we realized that the design was unable to hold itself up on the wall. Because of this, the design was changed entirely for functional reasons to the flat design you see now. While it is not as interesting of a shape, the new design increases the surface area of the treads on the wall and spreads out the weight, so it can effectively climb up the wall.